Connect the speakers to each other. The soundbar generates test tones that are projected into the room. Most surround sound systems have ports for each speaker that you simply plug the appropriate connector into. Although subwoofers are omnidirectional, placing them against walls and corners will amplify the bass, making it difficult to control. Verify that you have all of the cables that you need.
This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Angle the front speakers towards the audience. Place the subwoofer near the center of the home theater. Make sure to leave some slack at each end to keep the connection from becoming stressed.
It helps when sound pans from left to right, and keeps dialog synced with moving mouths on the screen. If your source devices do not have this option, they will most likely have a digital optical or analog option. If you have a room with one, or more, open ends, senior dating north wales a digital sound projector may not be your best soundbar choice. Arrange the speakers and their wires before connecting anything. Most soundbars can be wall mounted.
How to Set Up a Surround Sound Speaker System - dummies
After you place the subwoofer and are satisfied with its bass response, you need to balance it with your sound bar so that is not too loud or too soft. Shown above are connections you may find on a basic soundbar. Another type of soundbar you might encounter is a Digital Sound Projector.
This allows you to stream music directly from your smartphone and other compatible devices. Next, you plug in a specially provided microphone into the sound bar to aid the sound bar setup. Another connection included on some sound bars is an Ethernet Network port.
Examine your available speakers. Place the back channel speakers behind the viewing area. Once connected, you not only need to balance the subwoofer with your soundbar, but you also need to balance the surround speakers so that they don't overwhelm the soundbar, reddit unspoken rules but are also not too soft. Already answered Not a question Bad question Other.
If the surround speakers have to connect to a subwoofer, place the subwoofer near the back wall in the best spot for the deepest, clearest, dating daan paniniwala bass output. These are used for basic audio. Online is usually cheaper.
This will enable you to raise and lower the volume of both at the same time, with the same ratio, so you don't have re-balance the soundbar and subwoofer every time you raise or lower the volume. This will continue until you shut off the source or until you shut off the receiver. If the soundbar does not come with wall mounting hardware or a template, check the user guide for more on what you need, and if the manufacturer offers the items as optional purchases. The subwoofer is omnidirectional sound, which means you will achieve similar results no matter where the subwoofer is placed.
Raise the surround channel speakers. The theater sound bars sound great. To accomplish this, you'll need to strip some of the wire away with wire cutters and then clip them into place on the back of the speaker. Exclude your subwoofer from this process unless otherwise directed by the manual. There are some soundbars mostly Vizio and Nakamichi that include both a subwoofer and surround speakers.
- Connect one end of your speaker wire to the back of a speaker, then connect that speaker to another speaker in sequence.
- This is ideal since the sound will come from where you're already looking.
- Although many sound bars come with a subwoofer, there are some that don't but may still provide you with the option of adding one later.
- The position and labeling may vary.
This eliminates wire running from the front to the back of the room, but restricts subwoofer placement, as it needs to be near the surround speakers. Place the surround channel speakers to the side of the viewing area. Your two surround speakers should be placed on either side of the viewing area, pointed directly at the audience.
Tips for Hooking Up Speakers
The software in the sound bar then analyzes the tones and adjusts beam driver performance to best match your room dimensions and acoustics. You can't unless you have a set of speakers to go with it. Plug your receiver into a power source. Some older systems have clips that you plug bare speaker wire into.
If you bought your surround sound set second-hand, you may have to buy the receiver separately. Digital Sound Projection requires a room where sound can be reflected off walls. Each speaker should be angled in slightly so that it points directly toward the center of the seating area. Most surround sound kits include a receiver. Unlike powered speakers, the average surround sound speaker can't project audio on its own.
Each surround sound system will have a slightly different set of instructions detailing the best way to set it up. You can use older connectors e. If your soundbar comes with a subwoofer, or you add one, you need to find a place to put it. The back channel speakers should be the same height as the surround speakers.
How to Set Up a Surround Sound Speaker System
Is this article up to date? Many sound bars include a subwoofer output. The microphone picks up the tones and transfers them back to the sound bar. If you prefer a sound base over a sound bar, make sure you take these factors into consideration.
Optical audio is the newest and clearest type of audio, and most modern receivers support it. Warnings Be extremely careful not to attach bare speaker wire to a plugged-in item, as doing so may result in a short or an electrical shock. While you can follow general instructions to get decent sound out of your speakers, russia free dating site the best way to optimize them for perfect sound is by reading their manual first. You may also have the choice of choosing digital optical or analog this may be detected automatically depending on which is connected.
The surround channel speakers are what give the effect of sound happening around the viewer. In these systems, the subwoofer is wireless, but the surround speakers connect to the subwoofer via speaker cables. Is a home theater sound bar as good as a receiver and multiple speakers? If you don't have the proper cables, you can find them online or in tech department stores. In addition to the digital optical, digital coaxial, and analog stereo audio connections, a higher-end sound bar may provide the following options.
How to Hook Up a Subwoofer to a Home Stereo
Tips for Hooking Up Speakers - dummies
Run wire from each speaker to the receiver. Check your remote control for separate volume level controls for the soundbar and the subwoofer. Cookies make wikiHow better. Tips You may have to tweak individual item settings before your surround sound system setup is complete. Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.
- Make sure that you have an audio receiver.
- Your surround speakers should be placed about two feet above ear level and angled down slightly so that they point at the audience.
- Also, check to see if the soundbar also has a master volume control.